http://thestampingrounds.typepad.com/my_weblog/2008/09/back-to-school.html
Here's how it is made: 1.
I took a 7"x11" piece of cardstock, and scored it crossways at: 1/2",
3-3/4", 4-3/4", 5-3/4", 9" & 10". I then rotated it to the
lengthwise direction, and scored it in at 1-1/2".
2.
I cut up each of the crosslines, up 1-1/2" (to that scoreline). I then
trimmed off the 1/2" tab (the first one), and cut each of the sections
of two down by half (just to make it a little less bulky to work with).
Now, some people would say to leave them in to add stability, so if you
are adding weight to your box, be sure to do that! Lastly, I trimmed
that long 1/2" scored area (the first one), but just adding a little 45
degree angle to each side - makes it easier to line up when you put the
box together.
3.
I used my Cropadile and punched holes where I wanted my ribbon to be.
*make sure you do this before anything else! It gets harder if you wait
until later - trust me, I know! (oops)* I went ahead and put my jumbo
eyelets into the bottom holes only, and then threaded them with ribbon,
leaving the ends hanging out (I tied a not on the backside, to keep
them from coming out.)
4. I assembled the box using sticky strip. By the way - got a
neat tip at convention on this - before you remove the red plastic from
the tape, run your bone folder over it, and it will loosen it from the
tape, making it easier to remove. Who knew?! :)
By the way, just a
little note: whenever I make a box, when I put the bottom edge
together, I always make sure that the flap that is attached to the FRONT
SIDE goes on last - it just makes it a little nicer looking, especially
when the flaps are close in size.
5. Ok, the box is almost done. Let's put it aside for a moment
and take out our BigShots (don't have one? Join my new Sizzix Club, and
get it and a swack of other stuff at a discount! See my
CLUBS page
for details!) Get out your TopNotes and Bigz Scallop Envelope dies (2
different dies). I used the Summer Picnic paper and Real Red Cardstock,
and I diecut one of each, with each die. Here's the result:
*note that the envelope is best created using the 'Crease Pad' -
just put the crease pad on top instead of the plastic sheet, and roll
it through - you'll get better scorelines that way*
6. Ok, now you
can't see it so well in the pics above (try clicking on them to make
them bigger), but there is a perforated line in each of them to make
them mounted, if you want. Well, we want! So, I trimmed the designer
paper's perforated line, so they would mount perfectly - here are the
results:
I repeated this with the Topnote one as well. By the way, I
use Tombow only these days when mounting paper - it just works like
nobody's business, and it ain't movin' once it's stuck! :)
7. Ok -
now I marked my holes in the box, onto the lid (the top note). I
punched these separately, and actually mounted my jumbo eyelets in the
top note BEFORE I attached it to the box. Makes it a heck of a lot
easier, and no one would notice anyway!
And then attached it using, you guessed it, Tombow to the box.
8.
I then threaded the ribbons through the holes, and tied a knot inside.
Note that I pulled the ribbon ALL THE WAY OUT FIRST, and then made the
knots even with each other, so I knew the straps would be even.
9. Ok, box finished, I now turned my attention to the little
'pocket' for the front. Now, some folks are making theirs a bit more
3D, and adding one more scoreline to the envelope. As I have several to
do, and little time, I'm just leaving the envelope as is - consider it
an option though! I used my 1/16" circle punch to punch a hole through
the middle for my brad - it's easier if you do this before you fully
assemble the pouch. I then put it aside, and turned my attention toward
the brad itself.
Ok - I grabbed a silver brad (the new ones on
page 184 - LOVE them!). I also grabbed one of my little real red craft
ink spots. Here's the cute part - Ry was my 'model' for this (he took
pics of me for other parts of this too, btw!) - cute, eh? Anyway, use
your 'brad' as a stamp, and stamp it into the ink. Then wipe it off.
Stamp it again, wipe it off - do this several times, and you will get a
matching brad for your project! What more appropriate than a star for
the teacher?! :)
Mount that puppy to your mini envelope, and then finish your envelope with sticky tape:
sorry for the icky lens - that's what you get for letting your 5 year old take pics all day with it! :)
10.
Ok - mount that baby to the box using sticky tape. Last but not least,
make the medallion for the front! I used the scallop circle punch, the
1-3/8" circle punch, and the 1-1/4" punch. I made the apple using the
'Tart and Tangy' stampset, and I recommend Real Red Craft Ink (so the
colour runs less), and a green marker of your choice.
Once your
image has dried, use your crystal effects to create the 'shiny apple'
look - you'll want to bite into it when you're done!! When it's dry,
punch it out, mount it on dimensionals, and voila! Your teacher's gift
is done!
Add in the teacher gifts (tylonal, chocolate, cute sticky notes,
hershey's kisses, etc), and you have your teacher's gift! Enjoy!!
I made this cute little box like the one I saw here. It was super easy! How-to here, but if you want a photo tutorial, please visit previously mentioned link.
I distressed
a scrap piece of the Ghostly Greetings, added some Chills &
Thrills rub-ons, and a tag I had made from the Eat, Drink, & Be
Scary stamp set from the Holiday Mini.
